View Profile: denman - Appliance Repair Forums

Today, 12:30 PM

denman replied to a thread Replaced GE wall oven and now No Lights No Clock No Power in Range, Oven, & Cooktop Repairs

You are welcome. Glad to hear that you are up and running.

6 replies | 34 view(s)

Today, 11:09 AM

denman replied to a thread Replaced GE wall oven and now No Lights No Clock No Power in Range, Oven, & Cooktop Repairs

The oven light, control board and fan usually get power from L1 to Neutral, so Neutral must be connected. Neutral and ground are not connected in...

6 replies | 34 view(s)

Today, 05:16 AM

denman replied to a thread Replaced GE wall oven and now No Lights No Clock No Power in Range, Oven, & Cooktop Repairs

I am not sure if I understand the following: I wired the ground to the ground from the feed and ignored the white neutral If you mean that the...

6 replies | 34 view(s)

09-18-2018, 04:18 PM

denman replied to a thread Jenn Air D156B oven does not function in Range, Oven, & Cooktop Repairs

It is just below the bake and broil elements. Note that these are usually mounted on the outside top of the oven cavity. Same area as the oven...

3 replies | 37 view(s)

09-18-2018, 02:35 PM

denman replied to a thread Short in Refrigerator. in Refrigerator or Freezer Repair

It is not recommended to use a GFI on a fridge. Try it on a non GFI circuit. This will tell you if it is really a short or just current leakage.

1 replies | 30 view(s)

09-18-2018, 02:32 PM

denman replied to a thread Jenn Air D156B oven does not function in Range, Oven, & Cooktop Repairs

I cannot find much info on this unit. Below is a link that has some info on it. https://drive.google.com/drive/folders/0BzIiBNwRIV4NTkozZ1AzbDFtZ1E...

3 replies | 37 view(s)

09-17-2018, 12:54 PM

denman replied to a thread Bosch will not close water fill valve in Dishwasher Repair

You say that it runs till the overflow switch is activated so it is not a valve problem because killing power to the valve does close it. I cannot...

1 replies | 34 view(s)

09-13-2018, 04:23 AM

denman replied to a thread Chest freezer not freezing in Refrigerator or Freezer Repair

crghsam Manufacturers Warranty, I doubt that very much but the seller may have put a warranty on it. Many used appliance stores do have a...

3 replies | 82 view(s)

09-11-2018, 11:56 AM

denman replied to a thread Maxima replaced boot wont drain in Washer Repair

The only thing I can think of is that you put it on upside down so that there are no belows drain holes at the bottom. Or perhaps hey are plugged...

1 replies | 66 view(s)

09-10-2018, 03:58 PM

denman replied to a thread ge VENT DRIVER ASSEMBLY question in Dishwasher Repair

Are you sure it is the vent open/close motor or could it be the fan motor? it should be on when the vent is open. Perhaps the following will...

2 replies | 67 view(s)

09-07-2018, 11:59 AM

denman replied to a thread Samsung Front Load Washer WF448AAP/XAA won't drain in Washer Repair

You never said but is it actually draining? Check for 120 volts across the drain motor/pump to see if it is getting power. If it is not getting...

6 replies | 228 view(s)

09-06-2018, 01:52 PM

denman replied to a thread Chest freezer not freezing in Refrigerator or Freezer Repair

Since the compressor is running and you are not getting any cooling I hate to say it but it is most likely a sealed system problem. Hopefuly the...

3 replies | 82 view(s)

09-06-2018, 09:35 AM

denman replied to a thread Heavy wash cycle select problem in Dishwasher Repair

I agree with you that the control board is the most likely culprit. Sounds like the other person did not look at this unit so thought that the...

1 replies | 39 view(s)

09-06-2018, 09:32 AM

denman replied to a thread samsung dryer runs for roughly a minute and shuts off in Dryer Repair

I am not sure about your model number. Yes if it uses drum rollers then they could cause the problems. Check that they spin easily and are not...

10 replies | 9757 view(s)

09-05-2018, 11:55 AM

denman replied to a thread Baking function won't work in Range, Oven, & Cooktop Repairs

Looks like convection coming on during pre-heat is normal. Unfortunately I cannot find any wiring info on between the control board and the relay...

3 replies | 97 view(s)

09-05-2018, 08:18 AM

denman replied to a thread Baking function won't work in Range, Oven, & Cooktop Repairs

Below is tech info on this unit. http://b2b.frigidaire.com/support/ResultsPage.asp?strModel=PLEB30T9FCC&User=&Search=Search Does broil and/or...

3 replies | 97 view(s)

09-05-2018, 08:03 AM

denman replied to a thread samsung dryer runs for roughly a minute and shuts off in Dryer Repair

It sounds like the motor is overheating and tripping it's internal thermal protect. Try turning the drum by hand in the correct direction. It...

10 replies | 9757 view(s)

09-04-2018, 08:47 AM

denman replied to a thread Samsung DV42H5200EW Dryer HE Code in Dryer Repair

I am assuming that you have done the diagnostic tests in my earlier posts and all of them gave the correct results. Therefore a bad board is the...

12 replies | 366 view(s)

09-04-2018, 05:10 AM

denman replied to a thread Samsung DV42H5200EW Dryer HE Code in Dryer Repair

I cant just replace they relays......is this true? Sort of. The relays can be replaced but you need desoldering/soldering skill. Also finding...

12 replies | 366 view(s)

09-01-2018, 06:58 AM

denman replied to a thread Frigidaire Fridge Evap fan not working in Refrigerator or Freezer Repair

Sounds like the control board is bad. Perhaps the following will help ...

1 replies | 53 view(s)

09-01-2018, 05:45 AM

denman replied to a thread Samsung DV42H5200EW Dryer HE Code in Dryer Repair

Then I assume you replace the entire board then? Yes In you opinion do you think replacing the control board would rectify my issue? I would do...

12 replies | 366 view(s)

08-31-2018, 09:45 AM

denman replied to a thread FEFL58GSA - Stove top and oven not heating in Range, Oven, & Cooktop Repairs

It would be worth your time to find the loose connection. Loose connections can often start heating up and can cause fires.

3 replies | 98 view(s)

08-31-2018, 09:34 AM

denman replied to a thread Samsung DV42H5200EW Dryer HE Code in Dryer Repair

I have the exact same issue.....where is the heater relay located on the control board? Goto the link inmy prvious post and it's/their location is...

12 replies | 366 view(s)

08-30-2018, 09:51 AM

denman replied to a thread FEFL58GSA - Stove top and oven not heating in Range, Oven, & Cooktop Repairs

The elements require the full 240 volts. Try flipping the breaker off/on slowly a couple times. Sometimes you can loose half the line without...

3 replies | 98 view(s)

08-28-2018, 07:34 PM

denman replied to a thread Burner wont heat in Range, Oven, & Cooktop Repairs

Below is info on this unit http://b2b.frigidaire.com/support/ResultsPage.asp?strModel=ffef3018lb&User=&Search=Search Remove power/unplug the...

1 replies | 58 view(s)

08-28-2018, 09:09 AM

denman replied to a thread Samsung DV42H5200EW Dryer HE Code in Dryer Repair

You are welcome. And thank you for getting back to us. Now when others search for a similar problem they will see what worked instead of just...

12 replies | 366 view(s)

08-23-2018, 06:16 AM

denman replied to a thread Sears Kenmore UltraWash delay hours switch in Dishwasher Repair

Your model number is incomplete. The 665 simply designates that the unit was made by Whirlpool. Sounds like you need a new control board. ...

1 replies | 81 view(s)

08-23-2018, 06:13 AM

denman replied to a thread RE:(No subject) in Refrigerator or Freezer Repair

Below is a link that has a service manual etc. that should help you figure it out....

1 replies | 48 view(s)

08-18-2018, 03:15 PM

denman replied to a thread HELP! Can't find part number in Refrigerator or Freezer Repair

I am not 100% sure on the following but the values shouldbe the same as in the unit link I gave. Thermistor values on page 40 Defrost heater...

3 replies | 94 view(s)

08-18-2018, 05:23 AM

denman replied to a thread HELP! Can't find part number in Refrigerator or Freezer Repair

You unit does not have a defrost timer. Defrost is controlled by the control board at the back of thye unit. I cannot find info specific to this...

3 replies | 94 view(s)

denman
Doc

Mini Statistics

More 1 Friend

F David Rudnick

Recent Visitors

Basic Information

Statistics

Total Posts

General Information

1 Friend

F David Rudnick

denman Doc

Mini Statistics

More 1 Friend

F David Rudnick

Recent Visitors

Basic Information

Statistics

Total Posts

General Information

1 Friend

F David Rudnick

denman
Doc