You can read through our return policy here: http://www.partsdr.com/pages/Return-Policy.cfm
Printable View
You can read through our return policy here: http://www.partsdr.com/pages/Return-Policy.cfm
I am getting the VO error for Frigidaire Dishwasher model number FGHD2433KB1. What is the part number (and link) for my unit?
Thanks.
This is the vent assembly for your model:
Vent & Fan Assembly - 154861101
http://media.partsdr.com/regular/154861101.jpg
I have a Frigidaire DW Model # BGHD2433KF1 Serial # TH12932876. I am getting the ER uo codes. Looks like I may need a vent fan? Is that correct?
The information in this thread would apply to your model. If you read through this thread, it should answer your questions.
This is the vent assembly for your model:
Vent & Fan Assembly - 154861101
http://media.partsdr.com/regular/154861101.jpg
I have model fghd2433kf1 and when it gets to the drain/heating portion of a cycle the display looks like the picture attached blinking, no error codes just ER flashing along with everything else shown,, the add rinse aid and energy button lights up top are also flashing. Attachment 216 Any thoughts?
The thread in the link below has more information on this error.
http://forum.partsdr.com/showthread.php?1235-ER-code-and-all-lights-are-flashing
I have a model PLD4375RFC2 with uo error code. Checked wiring and still get code. Pulled it out and observed the vent pulsing, fan starts ,switch clicks in and out. Will new vent assembly fix it? Do you have the part #?
These types of symptoms are usually from a failed vent fan. I would recommend to start by replacing the vent fan.
This is the vent assembly for your model:
Vent & Fan Assembly - 154861101
http://media.partsdr.com/regular/154861101.jpg
Hoping for some help here. This dishwasher is about to drive me crazy. I bought the replacement vent after getting Er uo as well. I installed it and all was well for a few weeks. Now the dish washer is doing the exact same thing. I can hear the vent attempting to close but after a few tries the Er uo comes up. I have a frigidaire gallery Frigidaire Model #: FGHD2433KF1.
What else could it be? I already replaced the vent. I can hear it trying to "do it's thing" but it never get's past that step.
Thanks for the speedy reply. I type this after just drying my hands having HAND WASHED dishes.... I'm not above it but I have this machine that can do the job just as good as I can :cool:. I disassembled the dishwasher and found the service manual. I ran the dishwasher through the diagnostic test and the only error is the Er uo. I have not had this new vent for more than six months. Is there anything I can do to tell if this is limited to the vent or if the problem is actually the controller board. I have my multimeter leads in hand.....
I am getting the VO error for Frigidaire Dishwasher model number FGHD2433KW1. What is the part number (and link) for my unit?
This is the vent assembly for your model:
Vent & Fan Assembly - 154861101
http://media.partsdr.com/regular/154861101.jpg
I had the same problem and the fix is possibly simple like mine.
What isn't simple, is getting to the vent & fan assembly that ER UO code is directed at.
First, when you start the wash cycle, do you get three tapping sounds and then the error code?
If so, proceed ........
After you do the hard work and pull the unit out, the assembly is on the top right rear of the dishwasher.
Reach inside and unscrew the mount ring, then turn the vent & fan assembly over.
Remove two small screws and then you can remove the vent & fan assembly cover.
You will find a rubber valve that is controlled by a small solenoid.
Remove the rubber valve and clean (mine was VERY scuzzy) ....please make note of the valve position before removal.
** The sensor that tells the control unit if the valve is open or not, is controlled by a plastic tab on the valve assembly, so please be careful while cleaning!
Reassemble the vent & fan assembly and again, please be careful because this assembly is not inexpensive.
Replace the vent & fan assembly and reinstall the dishwasher ...you should be ready to test.
My unit worked perfectly after the clean job :)
If this doesn't fix the dishwasher, most likely you will need a new vent & fan assembly.
My Frigidaire is blinking up er code. My model # is thus2433kb1. Can you please help me and tell me where this ventvis
I have a frigidaire model # fghd2433kb with error code u o. Would the above vent unit be the same or what should I look at? Thanks for your help
I have the same vent open problem, Frigidaire model PLD4375RFC0. Do I need just the Vent & Fan Assembly #154861101 or do I need the one with the wire harness #5304467317? Thank you very much for your help.