Search:

Type: Posts; User: Doc Ryan

Page 1 of 20 1 2 3 4

Search: Search took 0.11 seconds.

  1. It looks like the wire and plug broke off of...

    It looks like the wire and plug broke off of another part. Better look to see if you can figure out where it previously attached.
  2. Not normally from what we have been seeing on...

    Not normally from what we have been seeing on these washers.
  3. Hi ahoss2000, We haven't seen a good way to...

    Hi ahoss2000,

    We haven't seen a good way to diagnose this type of issue you are having. Most often we see the suspension rods going bad causing these types of symptoms you are describing. If you...
  4. The model number you provided is not complete. ...

    The model number you provided is not complete. Please click here for common locations to find the model number tag on your washing machine.
  5. Hi Larry, Pressing the test switch doesn't...

    Hi Larry,

    Pressing the test switch doesn't always do something. I think this ice maker has to be below a certain temperature before the switch will cycle the ice maker.
  6. Glad to hear you figured out the problem! I...

    Glad to hear you figured out the problem! I updated the status to FIXED.
  7. Replies
    1
    Views
    146

    I would guess either the filter head is bad or...

    I would guess either the filter head is bad or the water inlet valve is bad. You will want to remove the water lines at different areas of the fridge to try to determine if water is flowing up to...
  8. Replies
    1
    Views
    168

    There is a supply and return air passage that the...

    There is a supply and return air passage that the air from the freezer uses to get up to the ice maker compartment. One of those passages may be clogged with ice or frost. I would start by...
  9. Replies
    1
    Views
    152

    If you run the dryer on a air dry (no heat)...

    If you run the dryer on a air dry (no heat) cycle, does the dryer heat up?
  10. Replies
    1
    Views
    151

    To me it sounds like one of the control boards...

    To me it sounds like one of the control boards might be bad. There is a user interface control board underneath the buttons and there is a main control board that is located behind the bottom...
  11. Replies
    4
    Views
    461

    Below are the instructions (click to enlarge)...

    Below are the instructions

    (click to enlarge)
    591
  12. Thread: gas oven

    by Doc Ryan
    Replies
    2
    Views
    322

    Have you tried shutting off the power for 10-15...

    Have you tried shutting off the power for 10-15 minutes?
  13. Thread: Beeping oven

    by Doc Ryan
    Replies
    3
    Views
    346

    Is this a USA model?

    Is this a USA model?
  14. Replies
    11
    Views
    824

    Thanks for the update. I have updated this...

    Thanks for the update. I have updated this thread to FIXED.
  15. Replies
    2
    Views
    590

    I would guess maybe an intermittent water valve...

    I would guess maybe an intermittent water valve or timer problem. Next time it acts up you could do a voltage test to see if power is being sent to the water valve. You can also try testing the...
  16. It sounds like it isn't properly going through...

    It sounds like it isn't properly going through the automatic defrost cycle. After you replaced these parts did you manually melt all of the frost on the coil to get it caught up?
  17. Thread: Beeping oven

    by Doc Ryan
    Replies
    3
    Views
    346

    The model number that you provided does not come...

    The model number that you provided does not come up as a valid model number. Can you please double check it?
  18. Replies
    11
    Views
    824

    Did you have wet clothes in the drum when you ran...

    Did you have wet clothes in the drum when you ran the test cycle?
  19. Replies
    8
    Views
    2,564

    I think the next step would be to trace the wires...

    I think the next step would be to trace the wires from the hall sensor on the motor back to the control board to make sure there isn't a problem with the wiring. From what I can tell the two parts...
  20. Replies
    11
    Views
    824

    Did you check to see if the wires to the moisture...

    Did you check to see if the wires to the moisture sensor were reconnected properly?
  21. Replies
    11
    Views
    824

    On the normal cycle it using the moisture sensor...

    On the normal cycle it using the moisture sensor to adjust the cycle times. If there are no wet clothes in dryer it will progress the cycle faster to save energy.
  22. Replies
    7
    Views
    739

    Strangely the manufacture lists part number...

    Strangely the manufacture lists part number 12008382 for the control module with a note that says "Discontinued-Order By Model Number".
  23. Replies
    7
    Views
    739

    I would try checking the wiring and connectors...

    I would try checking the wiring and connectors between the control board and the door lock and sensor.
  24. Replies
    9
    Views
    811

    If the dishwasher filling up with too much water...

    If the dishwasher filling up with too much water during the 2:25 fill cycle then the water inlet valve may be bad or the water supply line to the dishwasher may have to much pressure and not be...
  25. Replies
    8
    Views
    2,564

    Do you have a copy of the wiring diagram that you...

    Do you have a copy of the wiring diagram that you could post here? I was not able to find a digital copy of it.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4