Search:

Type: Posts; User: Doc Ryan

Page 1 of 20 1 2 3 4

Search: Search took 0.24 seconds; generated 59 minute(s) ago.

  1. Thanks for the updates! Your diagnosis of the...

    Thanks for the updates! Your diagnosis of the centrifugal mechanism makes sense to me. I have updated this to FIXED.

    Here is a link to the motor for anyone else that needs it.

    3 Speed Drive...
  2. It's not likely that GE will cover it if it is...

    It's not likely that GE will cover it if it is outside of the manufacturer's warranty.
  3. I think the motor that test is referring to is...

    I think the motor that test is referring to is the motor in the ice maker assembly. Which part numbers have you replaced? Were they new original Whirlpool parts?
  4. I haven't disassembled one of these motors...

    I haven't disassembled one of these motors before, so I am not sure if that is normal or not.
  5. I would recommend that you reach out to a GE...

    I would recommend that you reach out to a GE certified technician to see what they say about the issue. With the symptoms that you are experiencing, we more commonly see this type of problem caused...
  6. Most of the time it is a bad ice maker that...

    Most of the time it is a bad ice maker that causes it to stop making ice, but let me know what you end up finding.

    Ice Maker Assembly - W10873791 (PD00030246)...
  7. I would inspect and clean or replace the clutch. ...

    I would inspect and clean or replace the clutch. I have seen oil get on the clutch and cause the washer to act like you are describing. Let me know what you find.

    Clutch Assembly - 285785...
  8. In the diagram below, it looks to me like it...

    In the diagram below, it looks to me like it would have to be either the part that you already replaced #16, or the control panel #1 (part # WB36T11141 (PD00086954)), or the cable that goes between...
  9. Yes, a bad drain pump can cause these errors. I...

    Yes, a bad drain pump can cause these errors. I always like the remove the pump and visually inspect it for anything that might be caught in it and damage to the impeller. You can also check to see...
  10. Replies
    1
    Views
    673

    Hi Cade, I would suspect that the Main Control...

    Hi Cade,

    I would suspect that the Main Control Board might be bad and not sending the proper power to the drain pump for it to run. Have you done a voltage test to see if the pump is receiving...
  11. Do you have the model number of the washer? ...

    Do you have the model number of the washer? https://partsdr.com/model-number-locator/washing-machine

    Do you see any grease/oil on the inside of the cabinet of the washer?
  12. The drain pump on this washer operates on 120V Ac...

    The drain pump on this washer operates on 120V Ac power, so if it is only receiving in the 45V range, that would cause the problem. The power is supplied from the main control board, so my guess is...
  13. Replies
    1
    Views
    643

    Try inspecting the splines on the driveshaft...

    Try inspecting the splines on the driveshaft where it connects to the basket drive hub on the top side and the rotor on the bottom side. Looks for anything stripped on either side.
  14. Replies
    1
    Views
    749

    Which part number are you replacing? Normally...

    Which part number are you replacing? Normally the thermostat wires can be connected to either of the terminals.
  15. Here is the service sheet for your model number: ...

    Here is the service sheet for your model number: https://www.whirlpooldigitalassets.com/content/dam/global/documents/201505/wiring-sheet-W10751694-RevA.pdf
  16. Which part number(s) were replaced?

    Which part number(s) were replaced?
  17. Replies
    1
    Views
    671

    I would guess that the control board that this...

    I would guess that the control board that this plug connects to may also be bad. Also, check on the video below that covers some more things to check.


    https://www.youtube.com/watch?v=dWpzVv37BHw
  18. Replies
    1
    Views
    1,760

    Try running the dryer on an Air Dry (no heat)...

    Try running the dryer on an Air Dry (no heat) cycle to see if it heats up.
  19. Replies
    12
    Views
    2,452

    Thank you for the update! I have updated this to...

    Thank you for the update! I have updated this to FIXED. These are good dryers, they last a long time.
  20. What were the symptoms that the washer was having...

    What were the symptoms that the washer was having originally before replacing the main control board?
  21. Thank you for sharing. I have updated the status...

    Thank you for sharing. I have updated the status of this thread to FIXED.
  22. Replies
    12
    Views
    2,452

    I have run into this exact same things many...

    I have run into this exact same things many times. It is frustrating. I am sorry you ran into this issue.
  23. Replies
    14
    Views
    1,310

    Jason, if you can start with a clean coil with no...

    Jason, if you can start with a clean coil with no frost on it and then run it for 15 minutes and post of photo of the coil that would be ideal.
  24. Yes, I have seen those on other models but I...

    Yes, I have seen those on other models but I don't see anything like that listed in the parts list for your model. Did he provide you with a part number for the part?
  25. As I said before, I don't know of a solution to...

    As I said before, I don't know of a solution to your problem. If you find a solution, let me know.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4