Search:

Type: Posts; User: denman

Page 1 of 19 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    1
    Views
    11

    A model number may help others help you. First...

    A model number may help others help you.

    First thing to try is remove power from the unit for a couple minutes to see if it will reset.
  2. Your comment about the Red side of the line...

    Your comment about the Red side of the line having a problem might point to a wiring problem in the dryer.

    The unit uses the Black to White to power the motor and control board. (120 volts)

    The...
  3. Replies
    3
    Views
    42

    Try asking for it on ApplianceJunk.com. There...

    Try asking for it on ApplianceJunk.com.

    There is a guy there that finds almost all tech info.
  4. OK so if I understand you the only problem is no...

    OK so if I understand you the only problem is no heat, correct?

    If the above is true the following applies.

    Try flipping the breaker off/on slowly a couple times. Sometimes you can loose half...
  5. Replies
    3
    Views
    42

    Below is a service manual...

    Below is a service manual
    https://drive.google.com/drive/folders/0BzIiBNwRIV4NV1ZxdzBFRkNmUEE

    Convertible Dishwasher
    16026945 Mayta...

    I am assuming that you have already unplugged the unit...
  6. Below is a link to a post on another forum which...

    Below is a link to a post on another forum which has the tech sheet.
    https://www.appliancejunk.com/forums/index.php?topic=21917.msg113066#msg113066

    Try running the diagnostics to see if an error...
  7. Replies
    2
    Views
    56

    First check for nicks etc on the fins. Next...

    First check for nicks etc on the fins.

    Next check that the dos are working correctly in the agitator, just Google "whirlpool agitator" and look at a couple youtube videos.
  8. Replies
    1
    Views
    50

    Below is tech info on this unit....

    Below is tech info on this unit.
    http://b2b.frigidaire.com/support/ResultsPage.asp?strModel=FGHD2433KF1&User=&Search=Search

    The first thing to try is resetting the control board.
    Either unplug...
  9. Replies
    1
    Views
    67

    I am just guessing here so you will have to open...

    I am just guessing here so you will have to open it up and try to find the cause.

    Since the scraping is relatively slow the first thing I would check is the drum seals.
    Next I would check for a...
  10. Replies
    1
    Views
    57

    I could not find a wiring diagram for this unit....

    I could not find a wiring diagram for this unit.
    You really need one so that you can check that they do nor change a wire pin position between the connectors re: pin 3 going to pin 5 as an example....
  11. Replies
    2
    Views
    112

    The following has some info on this unit...

    The following has some info on this unit
    https://drive.google.com/drive/folders/0BzIiBNwRIV4Nb0pXTTlDcGlXUWs

    I am not sure if you have the single or double heating element unit.

    It looks like...
  12. A model number may help others help you. Most...

    A model number may help others help you.

    Most dishwashers have brackets that hold the dishwasher to the cabinets on the sides.
    This stops the tipping.

    Also it may be possible to drive s screw...
  13. Replies
    1
    Views
    85

    Below is some tech info on your unit...

    Below is some tech info on your unit
    https://drive.google.com/drive/folders/0BzIiBNwRIV4Nb0pXTTlDcGlXUWs

    Looks like Neutral and L1 power the control board so you will have to trace that back to...
  14. Replies
    4
    Views
    173

    Note: I think there should be an E after the 4 in...

    Note: I think there should be an E after the 4 in the model number.

    I also cannot find any tech info on this unit.


    I cannot say if the sensor can be chanched from the front but it should not...
  15. Replies
    4
    Views
    173

    Since you said it comes up to temperature I doubt...

    Since you said it comes up to temperature I doubt it is an oven sensor problem.

    Does it seem to take longer to reach the set temperature?

    On most ovens the bake and broil elements cycle back...
  16. Replies
    3
    Views
    139

    I am assuming that the condenser/compressor fan...

    I am assuming that the condenser/compressor fan also stays on when the compressor is on.

    so my bets guess is that it is a control board problem.
  17. I cannot say if it is good or bad news. It is...

    I cannot say if it is good or bad news.
    It is basically the same as your tablet/cell phone etc. touch screens.
    And they last forever.

    I am not a fan of them because of the grease and steam...
  18. Replies
    158
    Views
    173,548

    I can tell you the most likely cause is the vent...

    I can tell you the most likely cause is the vent assembly.

    Below is info on this unit which may help you confirm that the vent is tha cause....
  19. Replies
    1
    Views
    53

    A model number may help others help you!!!

    A model number may help others help you!!!
  20. Replies
    3
    Views
    139

    The control board is the most likely culprit...

    The control board is the most likely culprit since you say that the thermistors are OK.

    It would not be a bad idea to measure the actual temperature in the freezer and the fresh food sections just...
  21. Looking up your model's parts it seems that the...

    Looking up your model's parts it seems that the keypad is glass (capacitive touch) so there are no switches to replace.
  22. Thread: Samsung washer

    by denman
    Replies
    1
    Views
    165

    I cannot find any info on the given model number....

    I cannot find any info on the given model number.

    Perhaps you can find something useful in the following site
    https://drive.google.com/drive/folders/0BzIiBNwRIV4NejF3MTA4T0lxb28
  23. Has it ever worked OK at this location? Have...

    Has it ever worked OK at this location?

    Have you tried it disconnected from the vent system?

    Have you checked the heating coil to be sure it is not grounded?

    have you checked the internal...
  24. Thread: No power

    by denman
    Replies
    1
    Views
    99

    "I no that will no prevent power to the control...

    "I no that will no prevent power to the control panel"
    This is incorrect. If the Neutral to L1` side of the line is missing there will not be power to the control board.

    The following has a tech...
  25. Replies
    2
    Views
    200

    I am not sure if the following is an exact match...

    I am not sure if the following is an exact match to your unit but it should be close.
    Hopefully it will be of use to you.

    https://www.youtube.com/watch?v=HJhjGFijie0
Results 1 to 25 of 454
Page 1 of 19 1 2 3 4