Search:

Type: Posts; User: denman

Page 1 of 9 1 2 3 4

Search: Search took 0.08 seconds.

  1. Check for a plugged/frozen drain tube which is...

    Check for a plugged/frozen drain tube which is under the evaporator coil at the back of the freezer.

    Also it looks like they use a wire wrapped around the defrost element to prevent freezing...
  2. You could shut the water off to the unit. Then...

    You could shut the water off to the unit.
    Then if it still leaks you know that it is probably a plugged defrost water drain tube.
  3. Replies
    2
    Views
    115

    Check that the wheels on the tray support all...

    Check that the wheels on the tray support all turn easily.

    If OK then probably the turntable motor is shot.
    https://partsdr.com/appliance-parts/mmv1153aaw-maytag-maytag-microwave/
    OR...
  4. Below is a*link to tech info on this unit...

    Below is a*link to tech info on this unit
    https://drive.google.com/drive/folders/0BzIiBNwRIV4NWWZET29FMzFablE

    Could be a number of things.

    Try turning the drum in the correct direction by...
  5. Replies
    1
    Views
    40

    Disconnect the hose at the machine and run water...

    Disconnect the hose at the machine and run water into a pail.
    Just to be sure water is getting to the unit (some hoses have a screen built into the sealing washer.

    If OK recheck the screen at the...
  6. Replies
    4
    Views
    123

    I think you move the door to the first stop...

    I think you move the door to the first stop (partially open).
    Then pull the door up and off the hinges.
  7. Replies
    2
    Views
    172

    It sounds like a timer problem. I cannot find...

    It sounds like a timer problem.
    I cannot find any tech info on this model so just have to guess at what is wrong.
    I think the timer is the same as the one used in an IJC22053.
    ...
  8. jd501501 I think it is the following ...

    jd501501
    I think it is the following

    https://partsdr.com/part/wh13x26637-water-valve-assembly/
  9. Replies
    11
    Views
    263

    I am not 100% sure about this. Remove the lint...

    I am not 100% sure about this.

    Remove the lint filter.
    Then on the inside of the dryer remove the 3 screws that hold the filter grill on.
    Carefully remove the grill and check that there is a...
  10. Replies
    11
    Views
    263

    Just to add to Doc Ryan's post. The moisture...

    Just to add to Doc Ryan's post.

    The moisture sensor is the two metal strips by the lint filter.

    When clothes are wet, moisture is between the bars.
    This provides a current path (resistance)...
  11. Replies
    1
    Views
    48

    Your model number looks incomplete. Whirlpool...

    Your model number looks incomplete.
    Whirlpool numbers are usually several letters then some numbers and then some more letters at the end.
  12. Check that the wall receptacle is properly...

    Check that the wall receptacle is properly grounded.

    You could try an appliance surge protector.
    They are available at Home Depot etc.
    A 1000 joule unit is recommended but a 750 joule will do in...
  13. Replies
    9
    Views
    183

    If water is still entering the unit with the...

    If water is still entering the unit with the float switch activated (open) then odds are that it is a fill valve problem.

    You can check this by measuring the voltage across the fill valve.

    If...
  14. Replies
    9
    Views
    183

    FYI The float switch is just a safety device to...

    FYI The float switch is just a safety device to prevent over filling if the control board fails and powers the valve for too long.

    It should only be activated if there is a problem.
  15. Replies
    3
    Views
    97

    The control board would have been my most likely...

    The control board would have been my most likely cause but you say that you have already replaced it.

    I would double check damper.
    Also check for the correct thermistor resistance at the control...
  16. Replies
    3
    Views
    97

    The temperature sensing thermistor is not on the...

    The temperature sensing thermistor is not on the board.
    There is one in the freezer and one in the fresh food section.

    Below is a manual which should be close to your unit....
  17. Check that the heater assembly is solid. Check...

    Check that the heater assembly is solid.
    Check that the dryer is not vibrating too much.
    A shaking dryer can blow a hot element.

    The high limit and thermal cut off may be blown.
    Often an overly...
  18. Thread: Dryer

    by denman
    Replies
    1
    Views
    100

    Check that the heater element is not grounded. ...

    Check that the heater element is not grounded.

    Unplug the unit and both wires to the coil.
    Check it with a meter, should be around 10 to 12 ohms.
    Then check from each side of the coil to the...
  19. I think it is ...

    I think it is

    https://partsdr.com/part/8182862-water-inlet-valve/#model-WFW9400SW01
  20. Replies
    1
    Views
    88

    Sounds like you lost the L1 side of the line....

    Sounds like you lost the L1 side of the line.
    Then when you turn on an element the L2 side of the line feeds through the element and then powers the control board.

    Try flipping the breaker off/on...
  21. Replies
    4
    Views
    218

    I cannot find a wiring diagram for this unit but...

    I cannot find a wiring diagram for this unit but if you can get to the track going to the Quick Rinse key you could try cutting it.

    You would loose Quick Rinse but all other functions would be OK....
  22. Replies
    8
    Views
    227

    Check that the compressor is running. You can...

    Check that the compressor is running.
    You can hear it but it should also be vibrating.
    If it is running then the capacitor is OK.

    If it is running then check in the freezer to see if there is...
  23. Manufacturers do not publish board schematics so...

    Manufacturers do not publish board schematics so odds are slim that someone has it.
    Perhaps something on the following will help.
    ...
  24. Replies
    1
    Views
    115

    I am assuming that when the compressor shut off...

    I am assuming that when the compressor shut off the condenser/compressor fan stayed on.

    Sounds like the compressor is overheating and tripping the overload.

    Check the compressor winding's with...
  25. Replies
    1
    Views
    94

    The following may help...

    The following may help
    https://drive.google.com/drive/folders/0BzIiBNwRIV4NSEhtV0YxUTRrbTA

    One thing to note is that just because a valve has continuity does not mean that it is OK.
Results 1 to 25 of 207
Page 1 of 9 1 2 3 4