Search:

Type: Posts; User: denman

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. I am assuming that when you replaced the parts...

    I am assuming that when you replaced the parts you also checked/cleaned the interior of the unit including the blower wheel.
    Try running it disconnected from the vent system to eliminate this as a...
  2. Thread: dryer broke

    by denman
    Replies
    1
    Views
    31

    Have you tried unplugging it for a couple minutes...

    Have you tried unplugging it for a couple minutes to see if it will reset?

    Also when you shut the door does it restart on it' own?

    Sounds like a control board problem.

    Below is a link to a...
  3. Replies
    3
    Views
    61

    First clean/check the filters in the unit. ...

    First clean/check the filters in the unit.


    Below is a service manual which I think is a close match to yours when it comes to the pump...
  4. Replies
    3
    Views
    61

    A model number may be helpful. Has the unit...

    A model number may be helpful.

    Has the unit ever worked correctly with the current plumbing set up.
  5. Replies
    4
    Views
    2,079

    The following should help....

    The following should help.
    https://drive.google.com/file/d/0BzIiBNwRIV4NdHdPZ21fRTM2eG8/view

    Check and clean the interior including the blower wheel.
    Check the lint filter sometimes they can get...
  6. Replies
    1
    Views
    16

    A model number might be helpful. The first...

    A model number might be helpful.

    The first thing to check on an electric dryer with no heat is the power.

    Try flipping the breaker off/on slowly a couple times. Sometimes you can loose half the...
  7. I as not familiar with your problem but at least...

    I as not familiar with your problem but at least can get you a service manual which may be useful.
    https://www.appliancejunk.com/forums/index.php?topic=22090.msg113508#msg113508

    With luck someone...
  8. Replies
    4
    Views
    117

    I am assuming that the thermal fuse you refer to...

    I am assuming that the thermal fuse you refer to is on the heating element assembly.
    Also that you checked for a grounded element.

    Check that the lint screen and vent ant back of the drum are...
  9. Replies
    1
    Views
    109

    I doubt surges and brown outs would cause this. ...

    I doubt surges and brown outs would cause this.

    It was probably a bad connection from day one.
    It could have been the connector ar a bad solder joint on the board.
    Bad connections look like a...
  10. Sorry but I do not know.

    Sorry but I do not know.
  11. Replies
    7
    Views
    254

    let's assume that the heater relay is faulty and...

    let's assume that the heater relay is faulty and the contacts are always closed. When the dryer starts overheating shouldn't the high limit thermostat open, which would open the circuit and prevent...
  12. Replies
    7
    Views
    254

    Sounds like you have had a rough ride. I would...

    Sounds like you have had a rough ride.

    I would say that your current problem is from the heater relay contacts always being closed. This could be that they are welded together or that the relay...
  13. Replies
    4
    Views
    117

    I do not have a wiring diagram for your unit but...

    I do not have a wiring diagram for your unit but have one for a 42H500 and am assuming it is a close match to yours.
    Am also assuming that you have the correct wiring diagram and that yo have...
  14. If it wasn't running, would it be warm? Yes it...

    If it wasn't running, would it be warm?
    Yes it could be, you should be able to feel it vibrating.

    What are the odds that I'm low on coolant after 18 years?
    I do not know the specific odds as...
  15. Hard to say what is going on here because you do...

    Hard to say what is going on here because you do not feel that the compressor is starting/running correctly.

    If the compressor comes on and stays on re: you should be able to feel it vibrating for...
  16. Replies
    6
    Views
    213

    I am not sure that this will work. Many units...

    I am not sure that this will work.

    Many units but not all, switch back and forth between the bake and broil elements in the bake mode.
    This provides a more even temperature profile inside the...
  17. Replies
    6
    Views
    213

    The following may help...

    The following may help
    https://drive.google.com/file/d/0BzIiBNwRIV4NSFpRaXZRc2kyYkE/view

    Near the end of the document.
  18. Replies
    6
    Views
    213

    Yes there are two igniters

    Yes there are two igniters
  19. Replies
    2
    Views
    171

    Below is a link to a service manual ...

    Below is a link to a service manual

    https://drive.google.com/file/d/0B-i5KqMA2RZwc21aazJCVGZaZ1k/view
  20. The board is located behind the control panel...

    The board is located behind the control panel (keyboard).

    Yes it may be worth it to try and get the board repaired.
    Problem is that I would feel better about this if there was tech info on the...
  21. I cannot find any tech info on this unit. Yes...

    I cannot find any tech info on this unit.

    Yes it does sound like a control board problem which unfortunately is no longer available.
  22. Replies
    8
    Views
    270

    I am not sure that the unit is actually...

    I am not sure that the unit is actually activating the cold and hot fill valves during diagnostics.
    See page 45 for the valves.
    Mode 3 says it activates the bleach valve
    Mode 4 says it activates...
  23. Belo is a link to a tech sheet. Try the...

    Belo is a link to a tech sheet.
    Try the diagnostics
    https://drive.google.com/file/d/0BzIiBNwRIV4NRHZXRjlQbk1PVzQ/view

    Since the compressor runs after unplugging the unit my guess is that the...
  24. Replies
    8
    Views
    270

    I think we all are. Should depend on what...

    I think we all are.

    Should depend on what connectors you are using to test.
    Common to one connector is the fill contacts re: they are closed with no water in the unit / open when full.
    Common to...
  25. Replies
    8
    Views
    270

    A model number would be useful. No this does...

    A model number would be useful.

    No this does not mean that the switch needs replacing.

    I am assuming you mean zero ohms re: a short.
    Also use the 200 ohm scale not the diode checking mode.
    ...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4