Search:

Type: Posts; User: Doc Ryan

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    1
    Views
    116

    That error code is tE which is a temperature...

    That error code is tE which is a temperature sensor error. Check the resistance using a multimeter of the temperature sensor. It should read approx 66K Ohms at 68F and 37K Ohms at 86F. If the...
  2. Thread: ge dishwasher

    by Doc Ryan
    Replies
    1
    Views
    283

    The part number has been changed from the...

    The part number has been changed from the original part number that was used for the upper rack, but GE does not say if they made any design changes to the part. Below is a link to this part.

    ...
  3. What does the frost pattern look like on the...

    What does the frost pattern look like on the evaporator coils?
  4. Replies
    2
    Views
    216

    You will most likely need to replace the master...

    You will most likely need to replace the master LED light (2 plug) in the refrigerator compartment. This one controls the power that is output to the other two LED light (1 plug) units on the...
  5. When the compressor isn't starting check the...

    When the compressor isn't starting check the blinking lights on the inverter board and look on the tech sheet to decipher what it means.
  6. Replies
    1
    Views
    210

    I don't think the loose part you found in the...

    I don't think the loose part you found in the bottom of the dishwasher has any relation to the cancel light blinking. If you remove the bottom kickpanel there is a tech sheet on the back side of the...
  7. How cold does it get in this room in the peak of...

    How cold does it get in this room in the peak of winter?
  8. Replies
    9
    Views
    516

    Can you tell where the clicking noise is coming...

    Can you tell where the clicking noise is coming from? Is it coming from a control board on the back of the refrigerator or the compressor?
  9. Poll: What is the temperature in the freezer where the...

    What is the temperature in the freezer where the ice maker is located? Can you put a thermometer in the ice bucket to check it?

    Thanks,
  10. Yes, they would need to be wet and there would...

    Yes, they would need to be wet and there would need to be a large enough load in the dryer that the items are brushing up against the moisture sensor bars next to the lint filter area.
  11. 1. Check the lever bottom of the clutch that...

    1. Check the lever bottom of the clutch that moves to engage/disengage the spin cycle. Also, check the small motor that is used to move the lever.

    2. Check to see if something is caught between...
  12. I think you had two separate issues. I think the...

    I think you had two separate issues. I think the control board with the display has been bad for quite some time. If you put a new control board in and the touchpad buttons still don't respond then...
  13. Are you running the dryer with a load of clothes...

    Are you running the dryer with a load of clothes in it? What you described with how dryers act when they don't sense any moisture in the clothes, so the dryer advances the time of the dryer and ends...
  14. Replies
    7
    Views
    377

    Which thermal fuse was originally blown? It...

    Which thermal fuse was originally blown? It isn't very likely that the thermistor would be causing this type of problem.
  15. It is rarely actually a problem with friction...

    It is rarely actually a problem with friction unless one of the drum roller wheels is seized up. More common on these Samsung dryers is the motor itself just being bad.
  16. Replies
    1
    Views
    206

    Hi Captaindan! First, I would inspect the door...

    Hi Captaindan!

    First, I would inspect the door catch that goes on the top of the tub of the dishwasher. If that looks good then I would start by replacing the door lock switch. Below are links...
  17. Thank you for taking the time to post these...

    Thank you for taking the time to post these instructions! I will Private Message you my email address, if you want to send me the original copy of the photos and text I can make this into a blog...
  18. I would probably start by replacing the ice...

    I would probably start by replacing the ice maker. There isn't really any good way to narrow down the problem much further on these refrigerators. You usually end up having to make an educated...
  19. Replies
    5
    Views
    398

    First I would compare the parts you received to...

    First I would compare the parts you received to the photos we have listed on our website to make sure they match. If those match then my guess is that the manufacture has bad information and they...
  20. Poll: It looks like the ice maker assembly should have...

    It looks like the ice maker assembly should have all of the parts you are trying to replace. The only part that I didn't see included with the new ice maker is the part on the very right side in...
  21. It looks like the wire and plug broke off of...

    It looks like the wire and plug broke off of another part. Better look to see if you can figure out where it previously attached.
  22. Not normally from what we have been seeing on...

    Not normally from what we have been seeing on these washers.
  23. Hi ahoss2000, We haven't seen a good way to...

    Hi ahoss2000,

    We haven't seen a good way to diagnose this type of issue you are having. Most often we see the suspension rods going bad causing these types of symptoms you are describing. If you...
  24. The model number you provided is not complete. ...

    The model number you provided is not complete. Please click here for common locations to find the model number tag on your washing machine.
  25. Hi Larry, Pressing the test switch doesn't...

    Hi Larry,

    Pressing the test switch doesn't always do something. I think this ice maker has to be below a certain temperature before the switch will cycle the ice maker.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4