Search:

Type: Posts; User: denman

Page 1 of 17 1 2 3 4

Search: Search took 0.21 seconds.

  1. Replies
    3
    Views
    60

    It looks like only the control panel/keyboard is...

    It looks like only the control panel/keyboard is in the door.
    The control board looks like it is on the right hand side.

    I cannot find any tech info on SHE units so cannot say how to get at it.
    ...
  2. Replies
    2
    Views
    137

    I do not want to butt in but it is unlikely that...

    I do not want to butt in but it is unlikely that the stove top problem has anything to do with the control panel or control board.

    On most stoves the stove top elements are controlled by infinite...
  3. Replies
    12
    Views
    62,073

    John.Cox What is your model number. You...

    John.Cox

    What is your model number.

    You tried auto after the cleanup but did you try timed dry?
  4. Thread: Samsung drought

    by denman
    Replies
    1
    Views
    30

    I am afraid I cannot be of much help here as I...

    I am afraid I cannot be of much help here as I cannot find any tech info on the unit where it gives info about the water system.
    Hopefuly someone else will jump in.

    Since it runs OK without a...
  5. You are welcome. Glad to hear that you are up...

    You are welcome.
    Glad to hear that you are up and running.
  6. The oven light, control board and fan usually get...

    The oven light, control board and fan usually get power from L1 to Neutral, so Neutral must be connected.
    Neutral and ground are not connected in the unit.
    This is so that it can be used with 4...
  7. I am not sure if I understand the following: I...

    I am not sure if I understand the following:
    I wired the ground to the ground from the feed and ignored the white neutral
    If you mean that the Neutral on the oven now has nothing connected then you...
  8. Replies
    3
    Views
    68

    It is just below the bake and broil elements. ...

    It is just below the bake and broil elements.

    Note that these are usually mounted on the outside top of the oven cavity.
    Same area as the oven door lock.

    Check a parts breakdown to confirm...
  9. Replies
    1
    Views
    66

    It is not recommended to use a GFI on a fridge....

    It is not recommended to use a GFI on a fridge.
    Try it on a non GFI circuit.
    This will tell you if it is really a short or just current leakage.
  10. Replies
    3
    Views
    68

    I cannot find much info on this unit. Below is a...

    I cannot find much info on this unit.
    Below is a link that has some info on it.
    https://drive.google.com/drive/folders/0BzIiBNwRIV4NTkozZ1AzbDFtZ1E
    See 16000446 Jenn-...
    The wiring diagrams are...
  11. Replies
    3
    Views
    60

    You say that it runs till the overflow switch is...

    You say that it runs till the overflow switch is activated so it is not a valve problem because killing power to the valve does close it.

    I cannot find any tech info on this unit so am guessing.
    ...
  12. Replies
    3
    Views
    101

    crghsam Manufacturers Warranty, I doubt that...

    crghsam

    Manufacturers Warranty, I doubt that very much but the seller may have put a warranty on it.
    Many used appliance stores do have a limited warranty.
  13. Replies
    1
    Views
    84

    The only thing I can think of is that you put it...

    The only thing I can think of is that you put it on upside down so that there are no belows drain holes at the bottom.

    Or perhaps hey are plugged though that seems unlikely with a new bellows....
  14. Replies
    2
    Views
    85

    Are you sure it is the vent open/close motor or...

    Are you sure it is the vent open/close motor or could it be the fan motor?
    it should be on when the vent is open.

    Perhaps the following will help....
  15. You never said but is it actually draining? ...

    You never said but is it actually draining?

    Check for 120 volts across the drain motor/pump to see if it is getting power.

    If it is not getting power check from Plug 10 P pin 3 to Plug 2P pin 1
  16. Replies
    3
    Views
    101

    Since the compressor is running and you are not...

    Since the compressor is running and you are not getting any cooling I hate to say it but it is most likely a sealed system problem.

    Hopefuly the unit is under warranty.
  17. Replies
    1
    Views
    40

    I agree with you that the control board is the...

    I agree with you that the control board is the most likely culprit.

    Sounds like the other person did not look at this unit so thought that the control panel (keypad) was electronic.
  18. I am not sure about your model number. Yes if...

    I am not sure about your model number.

    Yes if it uses drum rollers then they could cause the problems.
    Check that they spin easily and are not worn (this includes their shafts.

    Also check the...
  19. Replies
    3
    Views
    104

    Looks like convection coming on during pre-heat...

    Looks like convection coming on during pre-heat is normal.

    Unfortunately I cannot find any wiring info on between the control board and the relay board.
    So I cannot say which board is causing the...
  20. Replies
    3
    Views
    104

    Below is tech info on this unit....

    Below is tech info on this unit.
    http://b2b.frigidaire.com/support/ResultsPage.asp?strModel=PLEB30T9FCC&User=&Search=Search

    Does broil and/or convection bake run on this oven?
    If not then the...
  21. It sounds like the motor is overheating and...

    It sounds like the motor is overheating and tripping it's internal thermal protect.

    Try turning the drum by hand in the correct direction.
    It should turn fairly easily.
    You may want to try this...
  22. Replies
    12
    Views
    370

    I am assuming that you have done the diagnostic...

    I am assuming that you have done the diagnostic tests in my earlier posts and all of them gave the correct results.
    Therefore a bad board is the most likely cause.

    Replacing the board would fix a...
  23. Replies
    12
    Views
    370

    I cant just replace they relays......is this...

    I cant just replace they relays......is this true?

    Sort of.
    The relays can be replaced but you need desoldering/soldering skill.
    Also finding the correct relay can be difficult.

    Another...
  24. Replies
    1
    Views
    56

    Sounds like the control board is bad. Perhaps...

    Sounds like the control board is bad.

    Perhaps the following will help

    http://applianceservice.mabe.ca/documents/ElectronicRefrigeration_OnLine.pdf
    ...
  25. Replies
    12
    Views
    370

    Then I assume you replace the entire board then?...

    Then I assume you replace the entire board then?
    Yes

    In you opinion do you think replacing the control board would rectify my issue?
    I would do a little more troubleshooting.

    Have you tried...
Results 1 to 25 of 415
Page 1 of 17 1 2 3 4