Search:

Type: Posts; User: denman

Page 1 of 14 1 2 3 4

Search: Search took 0.08 seconds.

  1. Definitely not a good unit if there is no local...

    Definitely not a good unit if there is no local service!!!

    Here is a service manual perhaps it will help.
    Running diagnostics may also be useful....
  2. Replies
    1
    Views
    33

    I am not sure if water could get into the motor....

    I am not sure if water could get into the motor.
    I cannot get decent pictures of this motor so am not sure the below would apply.

    If possible remove the cover for the gears on the motor and...
  3. Replies
    2
    Views
    36

    Pull the wires off the water valve. Tape them so...

    Pull the wires off the water valve.
    Tape them so that they cannot short to each other or the fridge.
    Turn the water back on.
    If you get water flowing into the ice maker, then the valve needs...
  4. Replies
    1
    Views
    35

    Below is a link to info on this unit...

    Below is a link to info on this unit
    http://b2b.frigidaire.com/support/ResultsPage.asp?strModel=FES367ASG&User=&Search=Search

    Since the stove top elements work correctly power to the unit is OK....
  5. Replies
    1
    Views
    45

    Could be that the motor or a switch is toast. ...

    Could be that the motor or a switch is toast.

    Below is a link to a Frigidaire unit that has a good explanation of how this type of icemaker works....
  6. Replies
    1
    Views
    58

    This problem usually ends up with the motor being...

    This problem usually ends up with the motor being replaced.

    I am assuming that the drum turns relatively easily as it can put too much load on the motor if seals etc. are worn.

    There is also a...
  7. Replies
    1
    Views
    65

    Sorry but I find your post a bit confusing. So...

    Sorry but I find your post a bit confusing.

    So if I understand it the heating element is open re: infinite ohms.
    The defrost thermostat is also open.
    The above devices must be measured...
  8. Replies
    2
    Views
    109

    If I understand your post the unit was working OK...

    If I understand your post the unit was working OK but suddenly the timer/control board looks OK buy not of the elements heat up.

    Sounds like you lost half the line voltage.
    The control board and...
  9. Sounds like a control board problem to me. The...

    Sounds like a control board problem to me.

    The odds are high that the oven sensor is OK as the unit works properly in bake.

    Same applies to the broil element though I am 100% sure about this....
  10. Replies
    1
    Views
    106

    Yes you can buy a complete heater assembly see...

    Yes you can buy a complete heater assembly see below
    https://partsdr.com/part/dc97-14486a-heating-element-assembly

    But I would not do it as there can be a number of different causes for no heat...
  11. Sorry but I do not know, perhaps the original...

    Sorry but I do not know, perhaps the original poster will jump in and have an answer.

    I imagine for the fan to run the door must be closed or the unit made to think that the door is closed.
    But...
  12. Yes they are different. The hood cutoff should...

    Yes they are different.

    The hood cutoff should be infinite ohms (open) at room temperature.
    It closes when it gets hot and keeps the fan running till the unit cools down.
    Often the temperature...
  13. Replies
    1
    Views
    30

    Remove the rear panel in the freezer and check...

    Remove the rear panel in the freezer and check the evaporator coils.
    Sounds like you may have a defrost problem.
    If the coils are clogged solid with frost/ice so that the evaporator fan cannot pull...
  14. Since you were able to run the diags I assume...

    Since you were able to run the diags I assume that you have the tech sheet.

    Many tech sheets also give info on the pinouts from the keyboard so that you can check the keys with a meter.

    If you...
  15. I do not have the tech sheet. Did the diags...

    I do not have the tech sheet.

    Did the diags allow you to use all or most of the keyboard keys?
    if yes the I still think the control board is the most likely culprit.

    There is an outside...
  16. My first thought would be the control board and...

    My first thought would be the control board and then the control panel.

    Carefully check the ribbon cable that runs between the two for any broken tracks etc.

    Usually when it is a control panel...
  17. Just to be sure you found the right device it is...

    Just to be sure you found the right device it is in the control panel (door).

    Since it is OK next would be to check that the unit is getting power
    and that the wire nut connections are good.
  18. A complete model number maybe useful. You are...

    A complete model number maybe useful.
    You are nmissing 3 or 4 digits after the 8.

    Some unit have a thermal fuse mounted on or near the control board.
    Remove power from the unit and check the...
  19. Flipping the breaker just disconnects the power....

    Flipping the breaker just disconnects the power.

    Unplugging the unit disconnects the power, Neutral and ground.

    For most repairs it should not make a difference as long as you are sure that the...
  20. Have you checked the heating element or are you...

    Have you checked the heating element or are you just replacing it as you feel it is the most likely culprit?

    Can you restart the unit right after it shuts down?

    If you have to wait a couple...
  21. Replies
    1
    Views
    173

    First I would check the power at the terminal...

    First I would check the power at the terminal strip in the un it.

    Check for both L1 and L2 voltage (120 volts) and that you have 240 volts L1 to L2.
    If OK with the dryer off, try it also with the...
  22. Replies
    1
    Views
    169

    A model number and a part number may help you get...

    A model number and a part number may help you get an answer to this.

    Though it is a Bosch so tech info is difficult to get.
  23. Thread: Samsung Dryer

    by denman
    Replies
    9
    Views
    317

    I am also stumped by this. Everything that...

    I am also stumped by this.

    Everything that could cause a heater to overheat has been replaced!!!!!!!!!!!

    The only thing I can think of is that the drum is stalling every once in a while and...
  24. Sorry but I cannot find a wiring diagram for this...

    Sorry but I cannot find a wiring diagram for this unit so cannot be sure.

    I would think that since a freezer door is not opened too often thay would use the timer in cumulative mode.

    Perhaps...
  25. Thread: Samsung Dryer

    by denman
    Replies
    9
    Views
    317

    Sorry but I have never pulled that part of the...

    Sorry but I have never pulled that part of the ducting out of a unit.

    Did you check that the vent flaps on the outside of the house opened fully.

    Like you I am pretty well out of ideas.
    It...
Results 1 to 25 of 348
Page 1 of 14 1 2 3 4