Search:

Type: Posts; User: Doc Ryan

Page 1 of 20 1 2 3 4

Search: Search took 0.19 seconds.

  1. Replies
    4
    Views
    132

    Below are the instructions (click to enlarge)...

    Below are the instructions

    (click to enlarge)
    591
  2. Thread: gas oven

    by Doc Ryan
    Replies
    2
    Views
    78

    Have you tried shutting off the power for 10-15...

    Have you tried shutting off the power for 10-15 minutes?
  3. Thread: Beeping oven

    by Doc Ryan
    Replies
    3
    Views
    107

    Is this a USA model?

    Is this a USA model?
  4. Replies
    11
    Views
    289

    Thanks for the update. I have updated this...

    Thanks for the update. I have updated this thread to FIXED.
  5. Replies
    2
    Views
    184

    I would guess maybe an intermittent water valve...

    I would guess maybe an intermittent water valve or timer problem. Next time it acts up you could do a voltage test to see if power is being sent to the water valve. You can also try testing the...
  6. It sounds like it isn't properly going through...

    It sounds like it isn't properly going through the automatic defrost cycle. After you replaced these parts did you manually melt all of the frost on the coil to get it caught up?
  7. Thread: Beeping oven

    by Doc Ryan
    Replies
    3
    Views
    107

    The model number that you provided does not come...

    The model number that you provided does not come up as a valid model number. Can you please double check it?
  8. Replies
    11
    Views
    289

    Did you have wet clothes in the drum when you ran...

    Did you have wet clothes in the drum when you ran the test cycle?
  9. Replies
    7
    Views
    217

    I think the next step would be to trace the wires...

    I think the next step would be to trace the wires from the hall sensor on the motor back to the control board to make sure there isn't a problem with the wiring. From what I can tell the two parts...
  10. Replies
    11
    Views
    289

    Did you check to see if the wires to the moisture...

    Did you check to see if the wires to the moisture sensor were reconnected properly?
  11. Replies
    11
    Views
    289

    On the normal cycle it using the moisture sensor...

    On the normal cycle it using the moisture sensor to adjust the cycle times. If there are no wet clothes in dryer it will progress the cycle faster to save energy.
  12. Replies
    7
    Views
    179

    Strangely the manufacture lists part number...

    Strangely the manufacture lists part number 12008382 for the control module with a note that says "Discontinued-Order By Model Number".
  13. Replies
    7
    Views
    179

    I would try checking the wiring and connectors...

    I would try checking the wiring and connectors between the control board and the door lock and sensor.
  14. Replies
    9
    Views
    197

    If the dishwasher filling up with too much water...

    If the dishwasher filling up with too much water during the 2:25 fill cycle then the water inlet valve may be bad or the water supply line to the dishwasher may have to much pressure and not be...
  15. Replies
    7
    Views
    217

    Do you have a copy of the wiring diagram that you...

    Do you have a copy of the wiring diagram that you could post here? I was not able to find a digital copy of it.
  16. Replies
    11
    Views
    25,465

    Awesome! :D

    Awesome! :D
  17. The next thing that I would inspect the is frost...

    The next thing that I would inspect the is frost pattern on the evaporator coil to see if the refrigerator system is working properly.
  18. Thank you for the update, I am glad to hear that...

    Thank you for the update, I am glad to hear that the water valve fixed your problem. I have updated the status of this thread to FIXED.
  19. Replies
    7
    Views
    217

    Thank you for the reply. When you installed the...

    Thank you for the reply. When you installed the new parts did you clear the fault code afterwards? Have you gone through the troubleshooting steps listed in the tech sheet yet?
  20. What are you using to measure the temperature?

    What are you using to measure the temperature?
  21. It sounds like a problem you would probably want...

    It sounds like a problem you would probably want a professional to take a look at. If the refrigerator came with a warranty I would contact them to have them take a look at it.
  22. Replies
    4
    Views
    123

    The next step would be to check to see if there...

    The next step would be to check to see if there is 120v AC power being sent to the ice dispenser motor when the motor should be turning.
  23. Replies
    1
    Views
    88

    Yes I believe the balance rings are normally...

    Yes I believe the balance rings are normally filling with a liquid like anti-freeze. If you don't see anything that caused it to crack then replacing the balance ring will most likely take care of...
  24. Replies
    1
    Views
    56

    The hole in the outer tub does not sound normal...

    The hole in the outer tub does not sound normal to me. I haven't heard of any good ways to repair a hole in a plastic tub. If you find a good way to repair it please let us know.
  25. Replies
    7
    Views
    217

    Hi Eric, Can you please let me know which part...

    Hi Eric,

    Can you please let me know which part numbers you have replaced on the range so far?

    Thanks
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4