Results 1 to 3 of 3

Thread: Frigidaire Washer E47 Error Code

  1. #1
    Admin/Technician Doc Ryan's Avatar
    Join Date
    Mar 2011
    Location
    South Dakota
    Posts
    3,560

    Frigidaire Washer E47 Error Code

    Is your Frigidaire front load washer agitating but not going through the spin cycle? A common cause of this is a failed door latch assembly. This will register an E47 error code in the computer, to check for this hold down the start and pause/cancel keys simultaneously for 5 seconds. If you receive an E47 error code you will need to check the PTC on the door latch assembly, the "board thinks the door PTC circuit is open in spin". Remove the door latch assembly and measure the resistance of the PTC, it should be around 1500 ohms. If its much lower than that it needs to be replaced.

    This is the PTC. Measure the resistance between the two terminals.
    Click image for larger version. 

Name:	Door latch PTC.jpg 
Views:	89 
Size:	90.7 KB 
ID:	4

    Most NEW door latch PTC's that I measure usually read higher than 1500 ohm's, this particular one I measured was 1750 ohms.
    Click image for larger version. 

Name:	1750ohms.jpg 
Views:	56 
Size:	71.6 KB 
ID:	6

    Door Latch/Switch Assembly - 131763202
    Ryan

    PartsDr.com
    - Discount Appliance Parts & Accessories


    Please help keep our repair forum FREE by purchasing your replacement parts from our online store. Thank you for your support.

    Check out our Repair Videos on Youtube

    "Like" Parts Dr on Facebook


    Follow Parts Dr on Twitter

  2. #2
    We had recently been receiving the E47 error code from our Frigidaire washer (not completing/conducting final spin cycle) and per the video on "how to test the door lock", verified that the resistance reading of the door switch was low at 1280 ohms. We ordered the new switch from PartsDr and received it yesterday. After installing the new switch the washer has worked fine for 4 loads of laundry. The only issue is that the resistance of the new switch measured very high at 3410 ohms. (Per the video, 1600-1750 ohms is expected on a new switch.) Is there cause for concern?

  3. #3
    I joined this forum expecting that feedback for "Appliance Repair Help" would include feedback from PartsDr technicians. Clearly there is no longer anyone from PartsDr monitoring this forum. If like me, you are looking for their feedback, contact them directly, don't waste your time joining this forum.

Similar Threads

  1. Frigidaire Diswasher ER UO Error code [FIXED]
    By clipsh in forum Dishwasher Repair
    Replies: 160
    Last Post: 07-29-2019, 06:59 PM
  2. Maytag Neptune washer ND error
    By country22 in forum Washer Repair
    Replies: 9
    Last Post: 02-01-2018, 10:01 PM
  3. Whirlpool Duet washer - f02 error- need a pump
    By Toni Robinson in forum Washer Repair
    Replies: 1
    Last Post: 01-29-2012, 07:01 PM
  4. Kenmore Electric Range Oven lower burner not coming on. F-10 Error Code.
    By snackpack in forum Range, Oven, & Cooktop Repairs
    Replies: 1
    Last Post: 12-04-2011, 06:18 PM
  5. Kenmore Washer F21 Error But Water Is Draining?
    By Summerville in forum Washer Repair
    Replies: 0
    Last Post: 07-17-2011, 06:16 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •