Results 1 to 3 of 3

Thread: Whirlpool Duet fills with water overnight and now HF error code

  1. #1

    Whirlpool Duet fills with water overnight and now HF error code

    Model Number: GHW9400PL0
    Brand: Whirlpool
    Age: 6-10 years

    Hi. My whirlpool duet front load washer sometimes fills with water when not in use. I have read other posts on this page that say it is the water inlet valve. Could that also cause the washer to start working and then stop, and display the HF error code. Just wondering if I have two problems or could I be lucky enough to fix both problems with one part. Thank you.

  2. #2
    Admin/Technician Doc Ryan's Avatar
    Join Date
    Mar 2011
    Location
    South Dakota
    Posts
    3,530
    Both problems might relate to the water valve being bad. I think the error code you are getting might be FH instead of HF? See the information for that error code below.

    No water detected entering machine or Pressure switch trip not detected.

    If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.

    Or

    If the control has turned the water valves on and after 8 minutes the flow meter has detected 10.5 gallons of water passing through it, but has not detected the pressure switch trip, the valves will be turned off and the error code will flash.

    Press PAUSE/CANCEL twice to clear the display.

    Potential Causes


    If there is no water in the unit:
    Make sure that both valves at the water source(s) are turned on all the way.
    Check for plugged or kinked inlet hoses or plugged screens in the inlet valves
    Verify inlet valve operation
    If there is water in the unit:
    Verify Drain pump operation
    Pressure Switch Hose is in good condition and properly connected to Tub and Pressure switch
    Verify there is not a siphon problem
    Verify wire harness connections to; Inlet Valves, Pressure Switch, Drain Pump, Flow Meter, and Central Control Unit (CCU)
    Check all hoses for possible leaks
    Verify pressure switch operation
    Verify flow meter operation
    Verify CCU operation
    Ryan
    www.PartsDr.com - Discount Appliance Parts & Accessories

    Please help keep our repair forum FREE by purchasing your replacement parts from our online store. Thank you for your support.

    Circle Parts Dr On Google+

    "Like" Parts Dr on Facebook


    Follow Parts Dr on Twitter

  3. #3
    You need to check and change the pressure switch water hose. I had the same issue my washer would fill up so much it started seeping out the door. I noticed that my washer was not balanced and the presuure switch hose was hitting against the the clear dump water tube. You would be surprised that due to the washer not being leveled it caused the little black pressure hose to damage. I replaced it and did a diagnostic test and it is working like new.

Similar Threads

  1. Replies: 233
    Last Post: 11-14-2017, 08:58 AM
  2. whirlpool F33 error code
    By sancjr in forum Washer Repair
    Replies: 4
    Last Post: 11-05-2013, 09:39 PM
  3. Whirlpool Duet F30 Error
    By KristenB in forum Washer Repair
    Replies: 1
    Last Post: 09-19-2013, 05:34 PM
  4. Code HF on Whirlpool Duet Washer
    By Mkorns in forum Washer Repair
    Replies: 2
    Last Post: 02-04-2013, 09:53 PM
  5. Whirlpool Duet washer - f02 error- need a pump
    By Toni Robinson in forum Washer Repair
    Replies: 1
    Last Post: 01-29-2012, 07:01 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •