Whirlpool Duet washer has water sitting in tub every morning. Water Valve issue

[Doc Ryan]

Can i tighten the Inlet valve or does it have to be replaced???

If the valve is leaking it can not be tightened to fix the problem, it will need to be replaced.

[Cp1014]

Yes, if the washer is slowly filling up with water when the washer is not running, then the water inlet valve has a slow leak and it will need to be replaced. If you can get the model number from the tag on the door frame of the washer, I can look up the part number for you.

Hi I have the same issue. My model # is GHW9250MW0 Serial# CSP 4112939

Thank you!

[Doc Ryan]

Hi I have the same issue. My model # is GHW9250MW0 Serial# CSP 4112939

Thank you!

This is the water valve for your model washer:

Water Inlet Valve - Part# PD00002389

[sgtschultz]

Faulty inlet valve - leaking into tub when not using.

GE

GTWN4250D1WS. What inlet valve part number ?

Thanks

[Doc Ryan]

Faulty inlet valve - leaking into tub when not using.

GE

GTWN4250D1WS. What inlet valve part number ?

Thanks

This is the water inlet valve for your model washer:

Water Inlet Valve - Part # PD00027876 (mfg # WH13X22314)

[cowpie]

Doc - same issue. Filling with water when off. Need Valve Part Number.

Washer model number is Whirlpool Duet WFW9450WL00.

Thanks.

[Doc Ryan]

Doc - same issue. Filling with water when off. Need Valve Part Number.

Washer model number is Whirlpool Duet WFW9450WL00.

Thanks.

This is the water inlet valve for your model washer:

Water Inlet Valve - Part # PD00003021 (mfg # 8540751)

[croadfeldt]

Doc - same issue. Filling with water when off. Need Valve Part Number.

Washer model number is Whirlpool Duet WFW9450WL00.

Thanks.

Add me to the list of folks that need to replace inlet valves.

Model #GHW9400PL1

[Doc Ryan]

Add me to the list of folks that need to replace inlet valves.

Model #GHW9400PL1

This is the water valve for your model washer:

Water Inlet Valve - Part# PD00002389

[Slwillett]

Doc - same issue. Filling with water when off. Need Valve Part Number.

Washer model number is Whirlpool Duet WFW9550ww00


Thank you, Stephanie

[croadfeldt]

This is the water valve for your model washer:

Water Inlet Valve - Part# PD00002389

Thanks, ordered one from you folks. Much appreciated!

[glenmick]

I have the same problem, Doc. I have Whirlpool Thin Twin, model number LTG5243BNO.

[Doc Ryan]

I have the same problem, Doc. I have Whirlpool Thin Twin, model number LTG5243BNO.

This is the water valve for your model washer:

Water Inlet Valve - Part # PD00002373 (mfg # 285805)

[whirlpooluser]

I was wondering if the problem I am having with my Whirlpool washer (model #GHW9150PW0) is also the water inlet Valve. I've noticed over the last few days a small amount of water in the washer the day after using it. I always shut the water off when not using the washer via a device called Leaksmart (which closes the valve with a push of a button). I've also noticed a foul oder when the washer is running but the water in the basin does not seem to be dirty. And even though it appears to be a small amount of water, it soaked up a towel without decreasing the water in the basin. Running a spin cycle did get rid of it though. Thanks for your help.

[Doc Ryan]

I was wondering if the problem I am having with my Whirlpool washer (model #GHW9150PW0) is also the water inlet Valve. I've noticed over the last few days a small amount of water in the washer the day after using it. I always shut the water off when not using the washer via a device called Leaksmart (which closes the valve with a push of a button). I've also noticed a foul oder when the washer is running but the water in the basin does not seem to be dirty. And even though it appears to be a small amount of water, it soaked up a towel without decreasing the water in the basin. Running a spin cycle did get rid of it though. Thanks for your help.

If the water supply to the washer is turned off, then it would have to be something other than a bad water inlet valve causing your problem. Check to make sure the washer is draining the water properly and that no water is backing up from the drain back into the washer.

[whirlpooluser]

If the water supply to the washer is turned off, then it would have to be something other than a bad water inlet valve causing your problem. Check to make sure the washer is draining the water properly and that no water is backing up from the drain back into the washer.

Thanks for responding. I actually ran a spin cycle and got all the water out. Since then I've ran 3 loads of wash and the problem has not come back. Very strange.

[jedowden2]

Sounds like I am having the same issue. I have a whirlpool duet that has water in the drum the morning after I run the washer.

Model Number: GHW9150PW2
Serial Number: CST0108933

[Doc Ryan]

Sounds like I am having the same issue. I have a whirlpool duet that has water in the drum the morning after I run the washer.

Model Number: GHW9150PW2
Serial Number: CST0108933

This is the water valve for your model washer:

Water Inlet Valve - Part # PD00002389 (mfg # WP8181694)

[cdefilippis]

Same issue. Can a "Dr" confirm the inlet value part number for Whirlpool model GHW9400PW4, serial # CTS1201392. Thank you

[Doc Ryan]

Same issue. Can a "Dr" confirm the inlet value part number for Whirlpool model GHW9400PW4, serial # CTS1201392. Thank you

This is the water inlet valve for your model washer:

Water Inlet Valve - PD00003431 (mfg# WP8182862)