Page 12 of 12 FirstFirst ... 2101112
Results 221 to 232 of 232

Thread: Whirlpool Duet washer has water sitting in tub every morning. Water Valve issue

  1. #221
    Yes the F20 error is also related to the water valve.
    It is that the unit is not getting water.
    A bad valve could be responsible for both problems.

    I think the correct valve is WP8182862 but it is always a good idea to double check this when ordering

  2. #222
    Thank you for your help. I just placed my order for the valve, from your company. Have a great day.

  3. #223

    whirpool duet WFW9400VE01

    I believe I have the same issue on a whirpool duet WFW9400VE01. Can you provide me with the model number of the water inlet valve.

    Thanks in Advance,

    Rooster

  4. #224
    stlee

    The part number for your valve should be WP8182862

  5. #225
    Whirlpool Duet WFW9400VE01. Water filling up in the tub over a few days. Same Part#?

    The reason I ask is when I plug in my model# on your Store site (https://partsdr.com/part/8182862-water-inlet-valve/) it says "WE COULDN’T FIND THIS MODEL NUMBER".

    Please confirm.
    Last edited by buntu1; 07-29-2017 at 01:21 PM.

  6. #226
    Buntu1
    Yes I believe it is the same part number

  7. #227
    I have a stacked GE spacemaker WSM2420SCZWW. I only wash in cold so the hot water supply valve is always off. Also, I always turn the cold supply off when not in use.

    Because I was on vacation the washer was not in use for almost 3 weeks. When I went to do a load last night after putting some clothes in I noticed they were immediately wet and there was water in the top loading drum (about 1-2 inches above the drum base) - I don't remember if it was completely clear water or not. I continued with washing and all seems fine. There is no visible water in the drum now but it sounds like there may be a slow drip somewhere as it faintly echoes. Again, the supply lines are off. I can't figure out why this happened and if it is slowly filling below the level of the drum. Could this be the water inlet valve that needs to be replaced even though the shut off valves are off?

  8. #228
    Here is a manual for this unit.

    To check for bad faucet shut off.
    Remove both hoses at the machine then place them in a pail if you get water in the pail then one of the valves is leaking.

    I have not worked on this type of unit so the below is a bit of a guess.
    It looks like the tub ring at the top of the tub is the type that has water in it.
    This helps in balancing the tub assembly.
    Perhaps it is just slowly leaking out this water.
    This may be normal.
    Often if you move the tub back and forth you can hear the water in the ring sloshing around.

    Below is a service manual
    https://drive.google.com/drive/folde...XdidFJ6SHRPVzg

  9. #229
    Patient
    Join Date
    Sep 2017
    Location
    San Jose, CA
    Posts
    1
    Hi, I have a Whirlpool Duet Model #WFW9400SW01. It has an occasional puddle in the barrel the next morning after a wash. When I see it dripping I've pulled the plug and it continues to drip. Could you point me to the correct Water Inlet Valve for this model.

  10. #230

  11. #231
    Hi, I have a GE washer that also drips water into the tub when off, The model number is GTW680BSJ0WS. Could you advise me on the correct part to fix this problem? Thanks!

  12. #232

Similar Threads

  1. water dispenser in Ice/Water in Door unit won't cut off
    By John Rotty in forum Refrigerator or Freezer Repair
    Replies: 1
    Last Post: 07-01-2012, 01:34 PM
  2. Water Inlet Valve - Kenmore
    By kckr2001 in forum Refrigerator or Freezer Repair
    Replies: 3
    Last Post: 06-26-2012, 09:37 PM
  3. MAYTAG BRAVO - Tub bearing issue?
    By bdm8641 in forum Washer Repair
    Replies: 3
    Last Post: 01-30-2012, 12:09 PM
  4. Washer won't fill on any water temp. It does spin though.
    By chelpiper in forum Washer Repair
    Replies: 2
    Last Post: 01-26-2012, 07:40 PM
  5. Kenmore Washer F21 Error But Water Is Draining?
    By Summerville in forum Washer Repair
    Replies: 0
    Last Post: 07-17-2011, 05:16 PM

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •