Results 1 to 2 of 2

Thread: Whirlpool duet front load washer displayed E1 F6 code

  1. #1

    Whirlpool duet front load washer displayed E1 F6 code

    Model Number: WFW9151YW00
    Brand: Whirlpool
    Age: 1-5 years

    Our Whirlpool duet front load washer displayed code E1F9 and would not drain. Went online and saw how to check drain pump filter and that was the problem. Was clogged with you so cleaned it. Ran a small load in rinse and spin cycle and it then displayed E1 F6 code and would not stop filling. Stopped washer and it drained out fine but tried again and it just keeps filling until stopped. It does not fill when off, just when on. Help!

  2. #2
    Admin/Technician Doc Ryan's Avatar
    Join Date
    Mar 2011
    Location
    South Dakota
    Posts
    4,263
    Here is what the manufacture says about the F6 E1 error code.

    F6 E1 - Serial Communication Error
    The communication between the Central Control Unit (CCU) and the Motor Control Unit (MCU) cannot be sent correctly.

    Possible Causes/Procedure

    - Unplug washer or disconnect power.
    - Check that the power cord terminals are connected at the right position to the RFI filter (white-Neutral/ black-Line).
    - Make sure that the two ground switches are pressed correctly by the toe and rear panels.
    - Make sure that ground switches are installed correctly, are not broken, and that the green ground wires are connected correctly.
    - Make sure that both ground switches are not broken or scratched. - Make sure that all the ground harnesses (green wires) are connected correctly, and are not broken or with wires detached.
    - Make sure that all wire harness connections from the CCU (MI3 cavity), main Motor, and MCU are not broken or with wires detached, and that connector internal pins are visible.
    - Check for continuity from the MCU connector wires to CCU (MI3 cavity) connector.
    - If the continuity diagnosis failed, the Main Harness must be replaced.
    - Make sure that all the connectors are fully seated.
    - Check the drive system for any worn or failed components.
    - Plug in washer or reconnect power.
    - Verify the washer operation by running the Diagnostic Test cycle. See page 5.
    - After the diagnostic test has finished, unplug washer or disconnect power and wait for 15 seconds.
    Ryan

    PartsDr.com
    - Discount Appliance Parts & Accessories


    Please help keep our repair forum FREE by purchasing your replacement parts from our online store. Thank you for your support.

    Check out our Repair Videos on Youtube

    "Like" Parts Dr on Facebook


    Follow Parts Dr on Twitter

Similar Threads

  1. Code HF on Whirlpool Duet Washer
    By Mkorns in forum Washer Repair
    Replies: 4
    Last Post: 02-03-2018, 04:13 AM
  2. Whirlpool Duet Washer - F30 Error Code
    By Surendar in forum Washer Repair
    Replies: 1
    Last Post: 06-07-2016, 03:30 PM
  3. whirlpool front load washer
    By ablaine in forum Washer Repair
    Replies: 2
    Last Post: 10-28-2013, 06:03 PM
  4. Replies: 5
    Last Post: 10-04-2013, 08:38 PM
  5. whirlpool front load washer error code e1 and f6
    By gregaguilar in forum Washer Repair
    Replies: 1
    Last Post: 07-17-2013, 09:45 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •