Search:

Type: Posts; User: Mr Repairer

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Thanks for letting us know. I have updated the...

    Thanks for letting us know. I have updated the status of this thread to FIXED.
  2. This model had problems with the air damper door...

    This model had problems with the air damper door breaking.
    When this happens, the temperatures in the food compartment run too cold.
    You can remove the damper assembly and do a visual inspection...
  3. If the door seals have been checked and are...

    If the door seals have been checked and are sealing properly, then your problem is an iced-over defrost drain.
    Remove bottom freezer panel (two screws) and rear panel. Remove icemaker if...
  4. Replies
    1
    Views
    7,120

    Unplug the dryer. Remove the cover to terminal...

    Unplug the dryer.
    Remove the cover to terminal block and be sure the wiring is intact (not burned),
    Then remove the back cover to the control panel and check the push to start switch for...
  5. This F-10 Code means the control board is sensing...

    This F-10 Code means the control board is sensing a runaway temperature condition.

    **First, unplug the range and remove the back panel. Unplug the oven temperature probe at disconnect.
    Check...
  6. You will need to replace your cold control. This...

    You will need to replace your cold control. This is common in a refrigerator this age. The replacement is not complicated.
    Good luck!

    Here is the part you will need:

    Cold Control...
  7. Your model of Amana range does not use any type...

    Your model of Amana range does not use any type of fuse. The clock center control board is a common failure when the bake element burns out (i.e. shorts to ground and ruins the circuit board).
    ...
  8. The best solution to your problem is a SawZall...

    The best solution to your problem is a SawZall (reciprocating saw) with a metal cutting blade. You will be cutting thru the motor shaft next to the blower wheel. (With a new blade, this should take...
  9. You will need to replace the spark ignition...

    You will need to replace the spark ignition switch assembly. One of the ignition switches arced.
    The result would be "continual clicking".
    Be sure to unplug the range before repairing!
    Good...
  10. Replies
    3
    Views
    41,254

    This is how to take the dryer apart and remove...

    This is how to take the dryer apart and remove the element:
    1. Unplug the dryer
    2. Remove the top of the dryer--2 phillips screws in the rear
    3. Remove the screws for the control console and...
  11. Replies
    1
    Views
    4,751

    The most common part that fails on this model of...

    The most common part that fails on this model of Whirlpool washer
    is the Temperature Sensor Switch.
    http://www.partsdr.com/photos/regular/W10248240.JPG
    Part # W10248240
    (There is no easy way to...
  12. The control board is one of the more common...

    The control board is one of the more common failures on your model of GE Refrigerators.
    As you can see from you list of symptoms, the control board controls many components on the fridge.
    Replace...
  13. The heating element and thermistor are two common...

    The heating element and thermistor are two common failures on your Kenmore dryer.
    **First Unplug Your Dryer**
    Now to test the thermistor:
    1. Remove the bottom panel and locate the thermistor. ...
  14. The first thing I would check would be the...

    The first thing I would check would be the pressure switch hose. This is a common failure on this age of top load GE washers.
    You can diagnose this visually by removing the front panel and...
  15. Your idler pulley has failed--"surface of pulley...

    Your idler pulley has failed--"surface of pulley is uneven so belt won't stay on".
    When replacing, be sure to clean idler pulley "shaft" of gunk that coats the surface.
    (I.E. Good time to replace...
  16. Evaporator motor failure is common on this age of...

    Evaporator motor failure is common on this age of Maytag refrigerator. (I.E. I assume you do not have a defrost issue.)
    To confirm fan motor failure, gain access by removing the back panel in the...
  17. OK, Here we go. First you want to make sure your...

    OK, Here we go. First you want to make sure your dishwasher is filling with water properly. (I.E. Is it filling enough?) Now, Here's the tools you will need: **Torx Screwdriver with multiple bits...
  18. Replies
    2
    Views
    8,434

    Here is the best way to confirm where your leak...

    Here is the best way to confirm where your leak is from. Your description says
    "leaks on fills cycle."
    First run your machine so that the water leaks appears, then
    unplug and remove the wire...
  19. Replies
    1
    Views
    4,233

    From your description the bake element has...

    From your description the bake element has failed. The only heat in the oven is from the broil element which cycles during baking for uniform heat.
    You can do a visual inspection of the bake...
  20. Replies
    1
    Views
    4,142

    Your Refrigerator should be going thru defrost...

    Your Refrigerator should be going thru defrost cycles several times in a 24 hr period. It slowly builds up frost to the point of little or no air flow over the course of several days.
    There are...
  21. Replies
    1
    Views
    5,916

    Gas coil failure is a common problem. Here are...

    Gas coil failure is a common problem. Here are the parts you will need to make the repair.
    Gas Valve Coil Set - Part # PD00002350 (mfg # 279834)
    http://media.partsdr.com/regular/WPL279834.jpg...
  22. The oven igniter is the most common part to fail....

    The oven igniter is the most common part to fail. The igniter can glow but still be defective as the oven gas valve doesn't have the correct voltage to operate. You can use a volt meter to check...
  23. Replies
    3
    Views
    10,776

    I would be happy to help you! Here's how to...

    I would be happy to help you!
    Here's how to install the pressure switch on a Frigidaire top load washer:
    ** Unplug your machine
    ** Remove the water level knob--and remove the exposed 1/4 inch...
  24. Replies
    3
    Views
    10,776

    Your pressure switch needs to be replaced. ...

    Your pressure switch needs to be replaced.

    Pressure Switch - Part # PD00000266 (mfg # 134411600)
    http://media.partsdr.com/regular/134411600.jpg

    Have a great day!
  25. From your description of the symptoms, it does...

    From your description of the symptoms, it does sound like an evaporator fan motor.
    Here's how to replace:
    *Unplug the Refrigerator
    *Remove the back panel
    *Slide out the fan motor and housing...
Results 1 to 25 of 31
Page 1 of 2 1 2